Rear view mirrors Torque specification Name Nm lb-ft lb-in Bolt of fastening of an external rear-view mirror 10 - 89 Screw of fastening of an external rear-view mirror 2 - 18 Pos. Spare...
Rear-view mirrors — diagnostics and checks Inspection and verification 1. Check the validity of the customer's complaint. 2. Check visually for obvious signs of mechanical or electrical damage. Visual Inspection...
Rear view mirrors — Pinpoint tests PINPOINT TEST A: MIRRORS DO NOT WORK STATES DETAILS/RESULTS/ACTIONS A1: CHECK INTERIOR LIGHT DELAY FUNCTION. 1 CHECK the interior lamp delay function. • Is the interior...
Outside mirror — removal and installation Withdrawal 1. NOTE: Left hand drive vehicle shown, right hand drive similar. Detach the cover. 1. Release the clip. 2. Disconnect the glass fastening chute. 2. Remove...
Handles, locks, latches and entry systems Torque specification Name Nm Pound-foot Pound inch Tailgate Latch Screws 7 - 62 Hood latch screws 7 - 62 Door latch screws 5 - 44 Pos. Spare Part No Name 1 Tailgate...
Diagnostics and checks of entry systems Inspection and verification NOTE: Make sure the battery is fully charged before starting electrical system diagnostics. NOTE: Make sure the doors are open before...
Remote control transmitter programming NOTE: A maximum of four remote transmitters can be programmed for a vehicle. All remote transmitters must be programmed at the same time. NOTE: Before entering Remote...
Hood latch — removal and installation Withdrawal All cars 1. Remove the radiator air deflector. 2. Remove the grille. 3. Disconnect the hood latch electrical connector. Vehicles with air conditioning 4....
Front door latch — removal and installation Withdrawal 1. Remove the front door trim panel. See Section 501-05 for more information. 2. Remove the side impact energy absorption panel. 3. Remove the screw (in the...
Rear door latch — removal and installation Withdrawal 1. Remove the rear door trim panel. See Section 501-05 for more information. 2. Remove the side impact energy absorption panel. 3. Remove the screw (in the...
Latch of the raised luggage compartment door Withdrawal All cars 1. Remove the tailgate trim panel. 2. Disconnect and unplug the tailgate latch connector. «station wagon» 3. Release the tailgate latch cable from...
External door handle — removal and installation Withdrawal 1. Remove the front door trim panel. See Section 501-05 for more information. 2. CAUTION: Do not touch the surface of the adhesive as this will prevent...
Hood lock cylinder — removal and installation Withdrawal 1. Remove the hood latch. For more information, refer to the Hood Latch chapter available in this section. 2. Remove the hood lock cylinder. Installation 1....
Ignition lock cylinder — removal and installation Withdrawal 1. Disconnect a wire of weight from the accumulator. See Section 414-01 for more information. 2. Remove the bottom section of the instrument panel. 1. Remove...
Door lock cylinder — removal and installation Withdrawal 1. Remove the door latch. For more information, refer to the Front Door Latch chapter available in this section. 2. Remove the door lock cylinder....
Lock cylinder of the lifted luggage compartment door Withdrawal 1. Remove the tailgate latch. For more information, refer to the Tailgate Latch section of this section. 2. Cut off the tailgate lock cylinder body to expose...
Tailgate Lock Cylinder (Station wagon) Withdrawal 1. Remove the tailgate trim panel. 2. Remove the exterior trim molding and license plate light. Remove the screws. Disconnect the license plate light...
Internal door latch release handle Withdrawal 1. Remove the door trim panel. See Section 501-05 for more information. 2. Disconnect the door latch remote control handle. 1. Disconnect the handle from the...
Bumper Torque Specification Torque specification Name Nm Pound-foot Pound inch Front bumper bolts 25 18 - Rear bumper bolts 20 15 - Rear Bumper Cover Support Rail Nuts 5 - 44
Front bumper cover — removal and installation Withdrawal All cars 1. Remove the radiator air deflector. 2. Remove the grille. 3. Remove the headlight washers on both sides (in the presence of). 1. To access the...
Rear Bumper Cover (3-Door/5-Door) General equipment: Electric drill Drill bit 5 mm Cutter for hole 29 mm Cutter for 35 mm hole Cutter for hole 70 mm Withdrawal All cars 1. Remove the top push pins. 2....
Rear bumper cover (4-door) General equipment: Electric drill Drill bit 5 mm Cutter for hole 29 mm Cutter for 35 mm hole Cutter for hole 70 mm Withdrawal All cars 1. Remove the top push pins. 2....
Front bumper — removal and installation Withdrawal 1. Remove the front bumper cover. For more information, refer to the Front Bumper Cover chapter available in this section. 2. Remove the bumper. Turn out...
Rear bumper (3-door/4-door/5-door) Withdrawal 1. Remove facing of a back bumper. For more information, refer to the chapter Rear bumper trim / Rear bumper trim available in this section. 2. Disconnect the...
Rear bumper (station wagon) General equipment: Electric drill Drill bit 5 mm Cutter for hole 29 mm Cutter for 35 mm hole Cutter for hole 70 mm Withdrawal All cars 1. Remove the top push pins. 2....