Doors, locks and windows of the car Ford Scorpio 2

Removal and installation of a cover of a luggage compartment (Scorpio I)
Model with a pronounced angle between the tailgate glass and the luggage compartment. Withdrawal Disconnect ground wire (-) battery. Caution: Disconnecting the battery...

Removal and installation of a back door (Scorpio I)
Models with a gently sloping rear end and TURNIER. Withdrawal Disconnect ground wire (-) battery. Caution: Disconnecting the battery will erase the contents of the...

Removal and installation of the lock of a back door (Scorpio I)
Models with a gently sloping rear end and TURNIER. Withdrawal Open back door. Loosen the rear door inner lining see previous chapter . Unclip the drive rods and...

Removal and installation of a door (Scorpio I)
Withdrawal Open the door, unfold the locking device -shaded arrow- and disconnect the plug connector of the door wiring harness (the figure shows the left rear door)....

Door adjustment (Scorpio I)
For a FORD SCORPIO, the gaps around the perimeter of the doors are not adjustable, since the door hinges are welded. If the gaps around the perimeter are not the same,...

Removal and installation of facing of a door (Scorpio I)
Withdrawal Open the door and turn out 5 (at the back door 7) fastening screws -arrows- at the edges of the door trim. Front door: remove both caps above the door trim...

Removal and installation of the door lock cylinder (Scorpio I)
Withdrawal Remove door trim. Remove the black plastic clips from the door edge. Carefully peel off the protective film. Attention: The film tears very easily. Release...

Removal and installation of the door lock (Scorpio I)
Withdrawal Remove door trim. Remove the black plastic clips from the door edge. Carefully peel off the protective film. Attention: The film tears very easily. Disconnect...

Windshield (Scorpio I)
The windshield, as well as the glass of the rear door and the glass of the rear side doors, are glued directly to the flanges of the window openings. This ensures high...

Removal and installation of window glass (Scorpio I)
Withdrawal Remove door trim see p. 135 . Open the door and use a Phillips screwdriver to unscrew the screw securing the outer rubber seal of the door shaft on the side...

Removal and installation of the crank mechanism of the window lifter (Scorpio I)
Withdrawal Remove door trim see p. 135 . Remove the black plastic clips from the door edge. Carefully peel off the protective film. Attention: The film tears very...

Removal and installation of a cover of a luggage compartment (Scorpio II)
A car with a pronounced angle between the rear window and the luggage compartment. Withdrawal Disconnect ground wire (-) battery. Caution: Disconnecting the battery will...

Lock cylinder, trunk lid lock (Scorpio II)
A car with a pronounced angle between the rear window and the luggage compartment. Withdrawal Open the luggage compartment lid. Remove trim from luggage compartment lid...

Removal and installation of facing of a door (Scorpio II)
Withdrawal Door open. Power window model: Use a small screwdriver to pry the power window switch out of the door trim and disconnect its connector. Model without power...

Removal and installation of the lock and the external handle of a door (Scorpio II)
Removal is basically the same as for the SCORPIO model made before 8/94, see p. 135 . The following describes only the differences that the new model should pay...

Removal and installation of the door lock cylinder (Scorpio II)
Withdrawal Remove lock and outside door handle see previous chapter . Open the clip at the top of the central locking switch and remove the switch. Push the lock washer...

Removal and installation of window glass (Scorpio II)
Removal is basically the same as for the SCORPIO model made before 8/94, see p. 136 . The following describes only the differences that the new model should pay...

Removal and installation of lateral facing of a luggage compartment (Scorpio II)
Scorpio Turnier Withdrawal Open the rear door and remove the rubber seal from the body rebate in the area of the side trim. Press the trim clips with a suitable fork....

Removal and installation of a cover of a niche of a mouth of a fuel tank (Scorpio II)
Withdrawal Fuel filler niche cover. open the tank and remove as shown in the figure. Attention: The cap is only pressed into the filler body, both parts are made of...

Central locking system (Scorpio II)
The central locking system can be activated from the driver's seat, from the passenger's seat next to the driver and via radio remote control. The locks of the four...